What is Bouncit Raw?
Bouncit Raw throws your sound into a tempo-synced stereo ping-pong delay: the same delay engine from the full Bouncit, behind one knob. It adds width, depth, and movement to dry vocals, plucks, and stabs. The delay time is locked to a 1/4-note bounce so it stays in time with your project, and the output is auto-leveled so the wash never jumps in volume.
Quick start
Get a result with Bouncit Raw in under a minute.
- Insert it. Put Bouncit Raw on the track or bus you want to change.
- Turn ECHO up. Raise ECHO until it sounds right.
- Compare. Bypass the plugin in your DAW to hear the difference.
The interface
Controls
Header
- 1Fire Head: click the flame logo to open the About panel: what the plugin is, who made it and the trademark notices. Click anywhere in the panel to close it.
The knob
- 2ECHO: a single macro that controls how big the bounce gets. At low settings you get a subtle slap. Push it and feedback and wet level rise together for more repeats and a deeper wash, while the tail darkens and tightens for a dub feel. An equal-power dry/wet blend with a touch of output headroom keeps the level matched at every position, so it grows wider and deeper with no volume jump.
Key specs*
| Circular-buffer stereo delay | Fractional, linear-interpolated read taps drive the ping-pong: a 1/4-note on the left and a dotted-quarter on the right, tempo-synced to your project. |
|---|---|
| Filtered feedback loop | Each repeat passes through state-variable low-pass and high-pass filters, a light anti-aliased tanh saturator for tape-ish color, and a DC blocker to preserve headroom in the loop. |
| Anti-aliased output soft-clipper | Transparent at low levels with a tanh-shaped knee and a hard safety ceiling, so no knob position can drive a runaway level. |
| Constant latency | The delay reports zero latency regardless of the macro, so the host's plugin-delay compensation value never changes mid-stream. |
| One knob, hidden targets | ECHO is the only host-automatable parameter; feedback, filters, mix, output, and width are wrapped as non-automatable but still saved and restored with the plugin's state. |
| Controls | One knob, ECHO |
| Formats | macOS: AU, VST3, CLAP, AAX, Standalone. Windows: VST3, CLAP, Standalone |
* Key specs from the plugin page. Some specs may not be listed.
How do I use Bouncit Raw on a track?
- Insert it. Put Bouncit Raw on the track or bus you want to change.
- Turn ECHO up. Raise ECHO until it sounds right. At low settings you get a subtle slap. Push it and feedback and wet level rise together for more repeats and a deeper wash, while the tail darkens and tightens for a dub feel.
- Automate it. ECHO is the only control your DAW can automate, so one automation lane covers it.
What about the full Bouncit?
Love the bounce? The full Bouncit goes deeper. The Pro version adds independent L/R delay times with six note values, free-time mode, tape modulation, ducking, feedback saturation, freeze, full stereo width control, and 14 factory presets. Every control is explained in the Bouncit manual.
Keyboard and mouse shortcuts
These work in every Bouncit Raw format (AU, VST3, CLAP, AAX, Standalone).
| Reset a control to its default | Double-click the knob or slider |
|---|---|
| Scroll to change a value | Hover over a knob and scroll the mouse wheel |
Frequently Asked Questions
Is Bouncit Raw free?
Yes. Bouncit Raw is completely free: freeware, no trial, no nag screens, no expiration.
What does the ECHO knob do?
ECHO is a macro that drives a tempo-synced stereo ping-pong delay. Turn it up and your sound bounces left-to-right with feedback and wet level rising together, plus tone and headroom shaping: all auto-leveled so it grows wider and deeper with no volume jump.
Is the delay in time with my track?
Yes. The delay time is pinned to a tempo-synced 1/4-note bounce, with a dotted-quarter on the right channel for the ping-pong, so latency stays constant and the echoes stay in time with your project.
How is Bouncit Raw different from Bouncit (Pro)?
Bouncit Raw gives you the stereo bouncing delay behind a single, level-matched ECHO knob. The full Bouncit adds independent L/R delay times, free-time mode, tape modulation, ducking, freeze, stereo width control, and 14 factory presets.
Does Bouncit Raw run on Apple Silicon and Windows?
Yes. Bouncit Raw is a Universal Binary that runs natively on Apple Silicon (M1/M2/M3/M4) and Intel Macs, and ships as a 64-bit build for Windows 10 and 11.
Can I automate Bouncit Raw?
Yes: the single ECHO macro is the only host-automatable parameter. Every underlying engine control (feedback, filters, mix, output, width) is hidden from the automation list but still saved and restored with the plugin's state, so your automation lane stays clean.
Does Bouncit Raw add latency?
No. The delay reports zero latency via a circular-buffer read regardless of where you set the ECHO macro, so the host's plugin-delay compensation value never changes mid-stream.
Where can I find more about Bouncit Raw?
On the Bouncit Raw page: its features, system requirements and how to get it.
How do I get and install Bouncit Raw?
- Get it. Bouncit Raw is free. Get it from the Bouncit Raw page.
- Run the installer. On macOS, double-click the .pkg file and choose AU, VST3, CLAP, AAX or Standalone. On Windows, run the .exe installer and choose VST3, CLAP or Standalone.
- Open your DAW. Restart your DAW and rescan plugins if needed, then find Bouncit Raw under Remi Blaze in your plugin list.
More about Bouncit Raw, including its features and system requirements, is on the Bouncit Raw page.
Where are the plugin files?
If you need to find Bouncit Raw on disk, for example to troubleshoot or to uninstall it manually, these are the standard locations.
| macOS AU | ~/Library/Audio/Plug-Ins/Components/ |
|---|---|
| macOS VST3 | ~/Library/Audio/Plug-Ins/VST3/ |
| macOS CLAP | ~/Library/Audio/Plug-Ins/CLAP/ |
| macOS AAX | /Library/Application Support/Avid/Audio/Plug-Ins/ |
| Windows VST3 | C:\Program Files\Common Files\VST3\ |
| Windows CLAP | C:\Program Files\Common Files\CLAP\ |
To uninstall, quit your DAW and delete the Bouncit Raw file from the relevant folder. Your DAW will stop listing it on its next rescan.
Need help with Bouncit Raw?
If something isn't covered here, or Bouncit Raw doesn't behave as described, contact support or email support@remiblaze.com. To get an answer faster, include:
- your operating system and version (for example macOS 15.6 or Windows 11)
- your DAW and its version
- the format you're using (AU, VST3, CLAP, AAX or Standalone)
- the version you installed (shown in the installer and in your download), since the About panel of every Raw shows v1.0.0
- what you did, what you expected, and what happened instead
This manual is for Bouncit Raw 1.0.2. Controls and settings can change between versions, so if something here doesn't match what you see, check the version shown in your installer or download. Spotted a mistake or have a question? Let us know.