Set threshold and ratio first: lower the threshold until the loudest hits lose a few dB, with a ratio around 2:1 to 4:1. Then set attack and release by ear. A slower attack lets the transient through for punch; a faster one catches it for control. Set the release so the level recovers before the next hit. Knee, lookahead and peak or RMS detection fine-tune the rest.

Threshold and ratio first

Put Furnix on the track and lower Thresh until the GR meter shows 2 to 4 dB on the loudest hits. Ratio sets how hard the level above the threshold is turned down. Around 2:1 to 4:1 levels a part gently; higher ratios start to catch peaks like a limiter.

Attack: punch or control

Attack is how fast the compressor reacts. A slow attack, around 10 to 30 ms, lets the first hit of each note through before the level drops, so drums keep their snap. A fast attack, a millisecond or less, catches the transient itself. That controls peaks, but too fast flattens the punch.

Release: recover before the next hit

Release is how fast it lets go. If the level is still down when the next hit arrives, the part sounds squashed. If it recovers too fast on a sustained sound, it can pump. Watch the GR meter fall back between hits. Grid Sync locks the release to your tempo, and Auto blends it by crest factor.

Fast attack Slow attack Fast release Slow release Tight control Catches transients, recovers fast. Can pump on rhythmic material. Punchy Lets the attack through, recovers fast. Adds snap. Flat Catches everything, holds on. Smooths dynamics evenly. Glue Lets the attack through, holds the body. Bus and mix glue. Diagram by Remi Blaze · remiblaze.com Fast attack / Fast release Tight control Catches transients, recovers fast. Can pump on rhythmic material. Slow attack / Fast release Punchy Lets the attack through, recovers fast. Adds snap. Fast attack / Slow release Flat Catches everything, holds on. Smooths dynamics evenly. Slow attack / Slow release Glue Lets the attack through, holds the body. Bus and mix glue. Diagram by Remi Blaze · remiblaze.com
The four combinations of fast or slow attack and fast or slow release, and what each one does to the sound.

Knee, lookahead and detection

  • Knee sets how gradually compression starts around the threshold. A wide soft knee eases in and sounds smoother; a hard knee clamps right at the threshold.
  • Look (lookahead) lets the compressor see a transient coming and catch it cleanly. It adds a few milliseconds of latency, which your DAW compensates for.
  • PEAK switches detection between peak, which reacts to the highest points, and RMS, which follows the average level.
Tip Limiters and saturators have a knee too. The Clampit manual FAQ covers which limiter knee to start with, and the Torchit manual FAQ covers what its saturation knee changes.

How do I set a compressor with Furnix?

  1. Insert Furnix. Put Furnix on the track you want to control.
  2. Set the ratio. Start Ratio around 3:1.
  3. Lower the threshold. Lower Thresh until the GR meter shows 2 to 4 dB on the loudest hits.
  4. Set the attack. Start Attack around 10 ms. Slow it down for more punch, speed it up for more control.
  5. Set the release. Adjust Release until the GR meter falls back before the next hit, or turn on Grid Sync.
  6. Match the level. Raise Makeup until the compressed sound matches the bypassed level, then compare with BYPASS.

Frequently Asked Questions

Peak for catching fast transients, like drum hits. RMS for smoother leveling of sustained parts, like vocals, pads and buses. In Furnix the PEAK button switches between them.

It sets how gradually compression starts around the threshold. A soft knee eases in for a smoother sound; a hard knee clamps right at the threshold for tighter control.

To see a transient before it arrives, the compressor delays the audio by the lookahead time. In Furnix that is up to 5 ms, and Furnix reports it to your DAW, which compensates so your tracks stay in time.

Usually the attack is too fast, so the compressor catches the hit itself. Slow Attack down until the snap comes back, or blend in the dry signal with Mix.

Plugins in this post

This tip uses Furnix 1.1.0 and Clampit 1.1.0. Some steps may differ, or not apply, if you're on a different version. Tried this workflow, or got stuck along the way? We'd love to hear from you: contact us.

More on dynamics

All dynamics posts →